|
PRODUCT NAME
|
Material Type; reforcement filler plus PTFE
|
Max. PV
(psi-fpm); Mpa-m/s
|
FDA
Compliant |
Operating Temp. |
Compare to
|
Attributes/
Properties
|
Quote |
GLASS-FILLED
PTFE
25% Glass filled sht
|
25% short glass fibre; 85% virgin PTFE |
10,000; 0.35 |
No
|
minus 350F - plus 500F |
Rulon AR* |
Wear resistant, improved hardness, lower thermal expansion, lower deformation under load
|
GLASS-FILLED PTFE QUOTE |
| POROUS
PTFE |
Porous PTFE |
Not applicable |
No
|
Not applicable |
Not applicable |
Spongy |
PTFE GASKET MATERIAL QUOTE |
ANTI-STATIC
PTFE |
5% amorphous carbon; 95% PTFE |
10,000; 0.35 |
No
|
minus 350F - plus 500F |
Not applicable |
Anti-static, improved wear, allows machinging to close tolerances |
AMORPHOUS CARBON-FILLED ANTI-STATIC PTFE QUOTE |
CARBON
FIBER-
FILLED PTFE |
5% carbon-25% carbon fiber; 95% PTFE
|
10,000; 0.35
|
No
|
minus 350F - plus 500F
|
Not applicable
|
Increased hardness, lower deformation under load; can be used in HF and strong alkali
where glass filled PTFE fails; less abrasive on mating surface
|
CARBON FIBER-FILLED PTFE QUOTE |
GRAPHITE-
FILLED PTFE |
5% graphite-15% graphite; Balance is PTFE |
10,000; 0.35 |
No
|
minus 350F - plus 500F |
Not applicable |
Excellent wear properties against soft metals;high load carrying capability in high speed
contact applications; chemically inert |
GRAPHITE-FILLED PTFE QUOTE |
BRONZE-
FILLED PTFE |
40%-60% Bronze powder; 60%-40% PTFE
|
10,000; 0.35
|
No
|
minus 350F - plus 500F
|
Rulon 142*
|
High thermal conductivity; better creep resistance; linear bearing material
|
BRONZE-FILLED PTFE QUOTE |
| GLASS-MOLY-FILLED
PTFE |
5/10/15% Glass fiber; 5% Molybdenum DiSulfide and 80-85% PTFE |
10,000; 0.35 |
No
|
minus 350F - plus 500F |
Not applicable |
Very hard and stiff; reduces friction; little effect on electrical properties; unreactive
chemically |
GLASS-MOLY-FILLED PTFE QUOTE |
MINERAL-
FILLED PTFE |
15% Mineral Fill and 85% PTFE
|
10,000; 0.35
|
Yes
|
minus 350F - plus 500F
|
Rulon 641*
|
FDA compliant
|
MINERAL-FILLED PTFE QUOTE |
| POLYIMIDE-FILLED
PTFE |
15% Polyimide and 85% PTFE |
7500; 0.26 |
No
|
minus 350F - plus 500F |
Rulon J* |
Good friction against soft metals |
POLYIMIDE-FILLED PTFE QUOTE |
STAINLESS
STEEL-
FILLED PTFE |
50/55% Stainless Steel; 45% PTFE
|
Not applicable
|
No
|
minus 300F - plus 500F
|
Not applicable
|
Very hard, very stiff
|
STAINLESS STEEL-FILLED PTFE QUOTE |
Fluoro-Plastics is a US based manufacturer of Teflon and PTFE products
